Free referral line · Independent guides, every cost sourced Calls answered 24/7 for water emergencies · 1-800-555-0199

Basements & Crawl Spaces · Problem guide

Basement Leak Repair: Leaking Walls and Foundations

Basement leak repair for leaking walls: how to fix a leaking foundation, seal basement wall cracks, tie-rod and block wall leaks, plus repair costs.

Short answer

Basement leak repair depends on where the wall leaks. A leak through a crack in a poured wall is usually sealed with polyurethane injection ($250–$1,000 per crack). Leaks through block walls, along many points, or at the wall-floor joint usually need an interior drain and sump pump or exterior waterproofing. Surface patches and paints rarely hold back water under pressure.

A leaking basement wall is easier to fix than a mystery wet basement, because you can see the entry point. The fix depends on the wall type and how many places it leaks.

Types of basement wall leaks

Leak Wall type Usual fix
Single crack Poured concrete Polyurethane or epoxy injection
Tie-rod holes (small round spots in rows) Poured concrete Plug or inject
Pipe penetrations Any Seal around the pipe
Mortar joints, many spots Block Interior drain with weep holes; exterior membrane
Whole wall damp Block or stone Drainage, exterior waterproofing
Wall-floor joint Any Interior perimeter drain

How to fix a leaking foundation

  1. Find and mark each entry point after a rain.
  2. Check outside first: downspouts, grading, window wells near the leak.
  3. Seal poured-wall cracks by injection from inside. See foundation crack repair.
  4. Drain block walls: weep holes at the base of each block core, an interior drain and sump.
  5. Exterior membrane where the wall itself is deteriorating or many points leak.
Poured walls usually leak at cracks; block walls leak through joints and hollow cores.

Sealing basement wall cracks yourself

Hardware-store patch kits and hydraulic cement can stop small, dry, non-moving cracks. They tend to fail on active leaks, wide cracks or cracks that move with the seasons. Horizontal cracks, stair-step cracks and bowing are structural and need an assessment. See bowing basement walls.

Basement leak repair cost

Repair Typical cost
Crack injection $250 – $1,000 per crack
Interior perimeter drain $40 – $120 per linear foot
Sump pump $600 – $2,500
Liquid membrane (exterior) $3 – $6 per sq ft
Excavation (exterior) $50 – $200 per cubic yard

Sources: Fixr, Angi.

Pro tip

Polyurethane injection stays flexible and is usually chosen for leaking cracks; epoxy is rigid and is used when the crack also needs to be bonded structurally. Ask which one is in the quote and why.

Leaking basement wall: inside vs outside fix

Seal from inside Fix from outside
Methods Injection, interior drain, membrane Excavation, membrane, footing drain
Disruption Basement only Yard and landscaping
Cost Lower Higher
Stops water reaching the wall No (manages it) Yes

Before you call

  • Note where the leak is and whether it's wet after every rain.
  • Check the gutters and downspouts directly above.
  • Look for cracks, tie-rod holes or pipe penetrations at the leak.
  • Photograph the wall wet and dry.

Tie-rod holes and pipe penetrations

Poured walls are built with metal ties that hold the forms; the round marks left behind can rust and leak. Pipes and wires through the wall leave gaps too. These are usually small, specific fixes: plug or inject the tie hole, seal around the penetration from inside or outside.

Block wall leaks explained

Concrete blocks are hollow. Water that gets through the outside face fills the cores and comes out at the bottom of the wall, at the cove joint, or through mortar joints lower down. That's why block wall leaks often look like a floor leak. Weep holes drilled into the bottom of each block core let that water drain into an interior perimeter drain.

Before you finish the wall

Never frame and drywall over a leaking wall. Fix the leak, run through a wet season, then finish with moisture-tolerant materials and leave space for air between the wall and insulation where your contractor recommends it.

Frequently asked questions

How do you fix a leaking basement wall?

Seal poured-wall cracks by injection; drain block walls with weep holes, an interior drain and a sump; use exterior membranes for widespread leaks.

How much does basement leak repair cost?

A crack injection costs about $250 to $1,000; drainage systems cost more.

Can a leaking basement wall be fixed from the inside?

Usually yes, with injection or an interior drainage system.

Is a leaking foundation a structural problem?

Not always. Leaks are a water problem, but horizontal cracks, bowing or displacement are structural.

Can hydraulic cement fix a leaking basement wall?

It can plug small holes and active leaks temporarily, but it's rigid and often cracks again when the wall moves.

Will sealing the inside of a block wall stop leaks?

Paints and sealers can reduce dampness, but water under pressure often pushes them off. Drainage is more reliable.

Why does my basement wall leak only at the bottom?

Often because water fills hollow blocks or presses at the cove joint, the lowest point of the wall.

Can waterproof paint stop a leaking basement wall?

It may reduce dampness but won't stop water under pressure.

Basement leak repair is cheapest when the wall is caught early. Call the number on this page and we'll put you through to a participating local waterproofing company.

Expert review: pending Waterproofing reviewer
Required credential:Basement Health Assoc. certified

Written and fact-checked by DryLevel editors, last updated 2026-11-16. Costs come from the sources linked in the article. Read our editorial policy or report a correction.

Call 1-800-555-0199